5.24
MB
〈Catalog〉Industrial Water Quality Measuring Instruments
Field-installation Type ORP Meter (Four-Wire Transmission)
HO-200 connects ORP sensor and measures ORP and temperature in the sample water. It is suitable for neutralization reaction treatment management of aeration tank, denitrification tank, etc.
ORP: -2000 - 2000 mV
Temperature: 0 - 100℃
Product name | ORP meter | |||
---|---|---|---|---|
Model | HO-200 | |||
Combined sensor | ORP electrode | |||
Measurable range | ORP | −2000 mV to 2000 mV (display range: −2200 mV to 2200 mV) | ||
Temperature | 0℃ to 100℃
| |||
Display resolution | ORP | 1mV | ||
Temperature | 0.1℃ | |||
Performance | ORP | Repeatability | Within ±5mV (response for equivalent input) | |
Linearity | Within ±5mV (response for equivalent input) | |||
Temperature | Repeatability | ±0.3℃ (response for equivalent input) | ||
Linearity | ±0.3℃ (response for equivalent input) | |||
Transmission output | Number of output point | 2 (the negative terminals for transmission outputs are internally connected at the same electric potential) | ||
Output type | 4 mA to 20 mA DC: input/output insulation type | |||
Load resistance | Max: 900Ω | |||
Linearity | Within ±8 mA (output only) | |||
Repeatability | Within ±0.02 mA (output only) | |||
Output range | Output 1 | ORP: Selection from preset ranges or free range setting within measuring range. | ||
Output 2 | Temperature: Free setting within a range between −20℃ and 130℃ | |||
Occasional out for error | Hold or burnout to either 3.8 mA or 21 mA | |||
Transmission hold | Selectable from transmission signal is held at the latest value or preset value. | |||
Contact output | Number of output | 3 | ||
Output type | No-voltage contact output | |||
Contact type | Relay contact; SPDT (1c) | |||
Contact capacity | 250 V AC 3 A, 30 V DC 3 A (resistance load) | |||
Contact function | R1, R2 | Selectable from upper limit alarm, lower limit alarm, ON/OFF control, currently holding of transmission output, and cleaning output (the contact is closed during alarm operation, opened normally and while the power is down). | ||
FAIL | Error alarm (Closed in the normal state, opened in the failure state or while the power is down). | |||
Alarm setting |
| |||
Control setting |
| |||
Cleaning output | Number of output points | 1 | ||
Output type | Contact output with voltage (output of connected power supply voltage) | |||
Contact type | Relay contact, SPST (1a) | |||
Contact capacity | 250 V AC 0.5 A | |||
External instrument | Solenoid valve for cleaning control | |||
Settings | Cleaning period | 0.1 hours to 168.0 hours | ||
Cleaning time | 2 seconds to 600 seconds | |||
Hold time | 2 seconds to 600 seconds | |||
Timer accuracy | Within 2 minutes per month | |||
Description of cleaning operation | One of the following operations.
| |||
Contact input | Number of input points | 1 | ||
Contact type | No-voltage "a" contact for open collector | |||
Conditions | ON resistance: 100 Ω max. Open voltage: 24 V DC Short-circuit voltage: 12 mA DC max. | |||
Contact function | External input for cleaning | |||
Communication function | Communication type | RS-485 | ||
Signal type | 2 wires system, isolated from the input circuit (not isolated from transmission circuit) | |||
Temperature measurement | Applicable temperature element | Platinum resistor: 1 kΩ (0℃) | ||
Positive relation resistor with temperature: 500 Ω (25℃), 6.8 kΩ (25℃), 10 kΩ (25℃) | ||||
Element selection method | Automatic temperature sensor type detection or manual selection (no temperature element is selectable) | |||
Calibration | ORP adjust function | Adjust (offset adjustment): −200 mV to 200 mV Span sensitivity correction: 0.500 to 1.500 | ||
Temperature calibration | 1 point calibration comparing reference thermometer | |||
Self-check | Electrode diagnostic error | Reference electrode impedance error (only applicable for differential circuit mode with a liquid contact electrode), temperature sensor short-circuit, temperature sensor disconnection, and out of the temperature measurement range | ||
Converter error | CPU, ADC, and EEPROM errors | |||
Operating temperature range | −20℃ to 55℃ (without freeze) | |||
Operating humidity range | Relative humidity: 5% to 90% (without condensation) | |||
Storage temperature | −25℃ to 65℃ | |||
Power supply | Rated power supply voltage | 100 V to 240 V AC ±10% 50/60 Hz | ||
Power consumption | MAX. 15 VA | |||
Others | With power switch for maintenance use | |||
Compatible standards | CE marking | EMC :EN61326-1 Class A, Industrial electromagnetic environment Safety :EN61010-1 RoHS :EN50581 9. Industrial monitoring and control instruments | ||
FCC rules | Part15 Class A | |||
Structure | Installation | Outdoor installation type | ||
Installation method | Mount on 50 A pole or wall | |||
Protection code | IP65 | IEC60529, JIS C0920 | ||
Case material | Aluminum alloy (coated with epoxy-denatured melamine resin) | |||
Material of fittings | SUS304 | |||
Material of hood | SUS304 (coated with epoxy-denatured melamine resin) | |||
Material of window | Polycarbonate | |||
Display element | Reflective monochrome LCD | |||
External dimensions | 180 (W) mm × 155 (H) mm × 115 (D) mm (excluding mounting brackets) | |||
Mass | Main body: approx. 3.5 kg, Hood and fittings: approx. 1 kg |
An arrester (spark over voltage: 400 V) is implemented for transmission output, contact input, and communication. However, use a most suitable surge absorption element on the connection lines in accordance with the ambient environment, the situation of equipment installed, and the externally connected equipment.
Do you have any questions or requests? Use this form to contact our specialists. * These fields are mandatory.