Semiconductors - Bildschirm Brett Chip

Back to Particle Characterization Products Overview
Back to Particle Applications

Particle Analysis of CMP Slurries

Chemical Mechanical Polishing (CMP) Applications

Chemical mechanical polishing (or planarization) is the most popular technique for removing the surface irregularities of silicon wafers. Typical CMP slurries consist of a nano-sized abrasive dispersed in acidic or basic solution. A chemical reaction softens the material during mechanical abrasion. The abrasive particles have a size distribution which directly affects critical metrics including rate of removal and wafer defects. Particle size analysis is therefore a key indicator of CMP slurry performance.

The typical size range of CMP abrasive particles is 50-250 nanometers and several particle sizing techniques are capable of measuring in this range with varying accuracy and precision. The typical oversize aggregate in CMP slurry is 1-10 microns and appears in the ppm range. The particle characterization challenge comes from the combination of accurately sizing the nano-scale particles while also identifying a relative few micron-scale aggregates.


Fine Particle Characterization in Chemical Mechanical Planarization (CMP) Slurries with Fluorescence Correlation Spectroscopy
with Prof. Edward E. Remsen | Bradley University, Mund-Lagowski Department of Chemistry & Biochemistry
and Tim Holt Applications Lab Manager | HORIBA Instruments, Semiconductor Segment

Fabrication of commercial integrated circuits depends critically on the physical and chemical properties of the abrasive slurry particles used to polish silicon wafer surfaces via chemical-mechanical planarization (CMP) to near-atomic flatness. The particle size distribution (PSD) of the abrasive particles is a key factor in the CMP process due to its connection with polishing efficiency and defect creation on wafers during polishing. In this presentation the utility of a single-molecule spectroscopic technique, fluorescence correlation spectroscopy (FCS), in this application is described. FCS stands out among PSD analysis methods based on its sensitivity to particles with hydrodynamic diameters in the sub-10 nm size range. Characterization of abrasive particles of smaller size in CMP slurries has become a requirement as the feature sizes of integrated circuits steadily decrease according to Moore’s law. The use of FCS in conjunction with a complementary technique, particle tracking using the Viewsizer 3000 multi-laser Nanoparticle Tracking Analysis (m NTA), is described as an approach to meet this challenge.

View on-demand webinar here

Particle Size by Laser Diffraction

Laser diffraction is the most popular technique for sizing CMP slurries owing to its fast, accurate, and precise measurements of both the nano- and micro-scale particles. The LA-960 Particle Size Analyzer can accurately measure particles from 10 nanometers to 5,000 microns, making this system an obvious choice for CMP applications. Our recent study to quantify the ability of the LA-960 to find a small number of oversize particles in the presence of the main population at 31 nanometers proves this point.

Webinar: Zeta Potential of CMP Slurries

In this webinar we will first review and discuss the importance of the iso-electric point of metal-oxide polishing agents and the role of slurry pH and then we will examine the effect of slurry fluid chemistry using ZP measurements to characterize the chemically-modulated development of surface charge of such polishing agents during aqueous polishing.

Particle Size by Dynamic Light Scattering

The SZ-100V2 Nanoparticle Analyzer system uses dynamic light scattering has one advantage over laser diffraction: the ability to measure sub-100 nanometer particles at very low sample loading (particle concentration). After the presence of any destructive large particles has been verified, CMP test labs may add a DLS system to complement existing technologies for characterization of the smallest particles.

Related Notes

Browse Products

Partica LA-960V2
mehr Partica LA-960V2

Laser Scattering Particle Size Distribution Analyzer

ViewSizer 3000
mehr ViewSizer 3000

Multi-Laser Nanoparticle Tracking Analysis (NTA)

mehr CS-900

Non-Contact Chemical Concentration Monitor

mehr HF-960EM

In-line Sensor & Auto Range Switching Concentration Monitor

Partica mini LA-350
mehr Partica mini LA-350

Laser Scattering Particle Size Distribution Analyzer

mehr CS-600F

Fiber Optic Type Chemical Concentration Monitor

mehr HP-480(W)

Industrial pH meter

mehr HF-960M

Low Concentration Type HF/HCl/NH3 Concentration Monitor


Do you have any questions or requests? Use this form to contact our specialists.