尺寸
5.24
MB
〈Catalog〉Industrial Water Quality Measuring Instruments
| Product name | Resistivity meter | |||
|---|---|---|---|---|
| Model | HE-200R | |||
| Combined sensor | 2-electrode method resistivity sensor (ERF-001 Series) of cell constant 0.01/cm | |||
| Measuring range | Resistivity | MΩ•cm | 0.000 to 2.000 | 0.00 to 20.00 (*Note 1) |
| kΩ•cm | 0.00 to 20.00 | 0.0 to 200.0 (*Note 1) | ||
| Temperature | ℃ | 0℃ to 100℃ (Display range: −10℃ to 110℃) | ||
| Display resolution | Resistivity | As shown in the measuring table. | ||
| Temperature | 0.01℃ | |||
| Performance | Resistivity | Repeatability | Within ±0.1% of the full scale (response for equivalent input) | |
| Linearity | Within ±0.5% of the full scale (response for equivalent input) | |||
| Temperature | Repeatability | ±0.1℃ (response for equivalent input) | ||
| Linearity | ±0.5℃ (response for equivalent input) | |||
| Transmission output | Number of output | 2 (The negative terminals for transmission outputs are internally connected at the same electric potential) | ||
| Output type | 4 mA to 20 mA DC: input/output isolated type | |||
| Load resistance | Maximum: 900Ω | |||
| Linearity | Within ±0.08 mA (output only) | |||
| Repeatability | Within ±0.02 mA (output only) | |||
| Output range | Output 1 | Resistivity: Free setting within a measuring range. | ||
| Output 2 | Temperature: Free setting within a range between −20 and 130℃ | |||
| Occasional out for error | Hold or burnout to either 3.8 mA or 21 mA | |||
| Transmission hold | In the maintenance mode, transmission signal is held at the latest value or preset value. In the calibration mode, transmission signal can be alive or held. | |||
| Contact output | Number of output | 3 | ||
| Output type | No-voltage contact output | |||
| Contact type | Relay contact; SPDT (1c) | |||
| Contact capacity | 250 V AC, 3 A; 30 V DC, 3 A (resistance load) | |||
| Contact function | R1, R2 | Selectable from upper limit alarm, lower limit alarm, and currently holding of transmission output. (The contact is closed during alarm operation, opened normally and while the power is down.) | ||
| FAIL | Error alarm (Closed in the normal state, opened in the failure state or while the power is down.) | |||
| Alarm setting range |
| |||
| Contact input | Number of input points | 1 | ||
| Contact type | No-voltage "a" contact for open collector | |||
| Conditions | ON resistance: 100 Ω max. Open voltage: 24 V DC Short-circuit current: 12 mA DC max. | |||
| Contact function | External input for transmission holding. | |||
| Transmission capability | Method | RS-485 | ||
| Signal type | 2 wire system, isolated from the input circuit Not isolated from transmission circuit | |||
| Temperature compensation | Applicable temperature element | Platinum resistor: 1 kΩ (0℃) | ||
| Compensation method |
| |||
| Temperature compensation range | 0℃ to 100℃ (However, the compensation calculation is extended lower than 0℃ or higher than 100℃.) | |||
| Calibration | Resistivity | Based on parameter input of coefficient for the sensor cell constant. | ||
| Temperature | Comparison to the accurate thermometer Both deviation and coefficient of RTD are taken into account for calibration. | |||
| Other function | UPW standard resistivity input | Select one from the next. 182.3 kΩ•m (standard), 181.8 kΩ•m, 182.4 kΩ•m, 18.23 MΩ•cm (standard), 18.18 MΩ•cm, or 18.24 MΩ•cm | ||
| Clipping function | If the measured value exceeds the user setting value for clipping, the measured data will be held at the clipping value. | |||
| Self-check | Sensor diagnostic error | Temperature sensor short-circuit, temperature sensor disconnection, and out of the temperature measurement range | ||
| Converter error | CPU, ADC, and memory errors | |||
| Operating temperature range | −20℃ to 55℃ (without freeze) | |||
| Operating humidity range | Relative humidity: 5% to 90% (without condensation) | |||
| Storage temperature | −25℃ to 65℃ | |||
| Power supply | Rated power supply voltage | 100 V to 240 V AC ±10% 50/60 Hz | ||
| Power consumption | 15 VA (max) | |||
| Other | With power switch for maintenance use | |||
| Compatible standards | CE marking | EMC :EN61326-1 Class A, Industrial electromagnetic environment Safety :EN61010-1 RoHS :EN50581 9. Industrial monitoring and control instruments | ||
| FCC rules | Part15 Class A | |||
| Structure | Installation | Outdoor installation type | ||
| Installation method | Mount on 50 A pole or wall | |||
| Protection code | IP65 | |||
| Case material | Aluminum alloy (coated with epoxy-denatured melamine resin) | |||
| Material of fittings | SUS304 | |||
| Material of hood | SUS304 stainless steel (coated with epoxy denatured melamine resin) | |||
| Material of window | Polycarbonate | |||
| Display element | Reflective monochrome LCD | |||
| External dimensions | 180 (W) mm × 155 (H) mm × 115 (D) mm (excluding cover and mounting brackets) | |||
| Mass | Main body: Approx. 3.5 kg; cover and mounting brackets: Approx. 1 kg | |||
Note
- Note 1 : Without temperature compensation, 0.0-100.0 MΩ•cm(0-1000 kΩ•m) can be displayed.
- Note 2 : When the sensor cable, the transmission cable, or the contact input cable is extended by 30 m or more, the surge test under the EMC Directive for CE marking is not applied.
- Note 3 : An arrester (spark over voltage: 400 V) is implemented for transmission output, contact input, and communication. However, use a most suitable surge absorption element on the connection lines in accordance with the ambient environment, the situation of equipment installed, and the externally connected equipment.
